The FULLSET operation fully sets the alarm system and provides full protection to a building (opening of any alarm zones activates the alarm).

On selecting FULLSET, the buzzer sounds and the keypad display counts down the exit time period. Exit the building before this time period has expired.

When the exit time period has expired, the system is set and opening of entry/exit zones starts the entry timer. If the system is not Unset before the entry timer expires, the alarm is activated.

The PARTSET A option provides perimeter protection to a building while allowing free movement through the access areas.

Zones that have been classified as EXCLUDE A remain unprotected in this mode. By default, there is no exit time; the system sets instantly on selection of this mode. An exit timer can be applied to this mode by enabling the Partset A timed variable.

The PARTSET B option applies protection to all zones except those that have been classified as EXCLUDE B.

By default there is no exit time; the system sets instantly on selection of this mode. An exit timer can be applied to this mode by enabling the Partset B timed variable.

The FORCESET option is presented on the keypad display when an attempt is made to set the system while an alarm zone is faulty or still open (the top line of the display shows the open zone).

Selecting this option sets the alarm and inhibits the zone for that set period.

The UNSET operation unsets the alarm. This menu option is only presented on the keypad after an Entry/Exit zone has been activated and a valid user code has been entered.

User can delay or cancel autosetting.

User can automatically override the Unset Delay. Only available for Financial installations. See Setting/Unsetting.

The RESTORE operation restores an alert condition on the system and clears the alert message associated with that alert condition.

An alert condition can only be cleared after the zone(s) or fault(s) that triggered the alert condition have been restored to their normal operating state and the CLEAR ALERT option in user programming is selected for that zone.

Inhibiting a zone deactivates that zone for one alarm set period.

This is the preferred method of deactivating a faulty or open zone as the fault or open condition is displayed on the keypad each time the system is being set to remind the user to attend to that zone.

Isolating a zone deactivates that zone until such time as the zone is de-isolated. All zone types on the controller can be isolated.

Use of this feature to deactivate faulty or open zones should be considered carefully; once a zone is isolated, it is ignored by the system and could be overlooked when setting the system in the future, compromising the security of the premises.

User can access panel through web browser.

This menu option displays the most recent event on the keypad display. The event log (see Event Log) details the time and date of each logged event.

User can create and edit other users on the panel but with only the same or less rights than this user.

This feature allows users to set up the SMS messaging service if a modem is installed on the system.

Use this menu option to program the time and date on the system (see Set Date/Time).

Ensure the time and date information is accurate; these fields are presented in the event log when reporting system events.

This menu option allows users to change their user PINs (see Change Engineer Pin).

Note: To comply with INCERT approvals, the user’s PIN code must contain more than 4 digits.

User can view video images via the web browser.
Note: The Web Access right must also be enabled for this function.

All zones that have the CHIME attribute set generate a short burst of audible tone on the keypad buzzer when they are opened (while the system is unset).

This menu option allows for enabling or disabling of the chime feature on all zones.

This option allows users to grant access to engineer programming.

For Swiss CAT 1 and CAT 2 regional requirements, when Engineer Access is granted, all areas must be unset otherwise the engineer will be denied access.

User can grant manufacturer access to panel to perform firmware upgrade.

User can activate/deactivate configured outputs (mapping gates). See Editing an output.

User can activate/deactivate configured X-10 devices.

Note: X-10 is in maintenance. The functionality remains in the system for backward compatibility.

User can lock/unlock doors.

User can control RF output

User can perform a bell test to test the external bells, strobe, internal bells and buzzer to ensure their correct operation.

User can perform a walk test to allow for testing of the operation of all alarm sensors on a system.

User can test a WPA.

User can test the seismic detector.

User can create and edit other users on the system with no restriction on user rights.

User can create and edit user profiles on the system.

User can configure calendars.

User can edit doors.