Addressing Mode
X-BUS addressing can be configured in one of the 2 following ways:
Automatic addressing
With automatic addressing, the controller over-rides rotary switches and automatically assigns expanders and keypads in the system unique IDs in sequential order.
Manual addressing
Manual addressing allows manual determination of each expander/keypad ID in a system. All devices should be installed where required and each ID set manually using the rotary switches. The zones to ID can be calculated using the following formula: ((ID value X 8)+1)= first zone number and then the next 7 sequential zones. For example ((ID2 x 8)+1)=17. Zone 17 is allocated to input 1 on ID2. Each input has the next sequential zone allocated to it, in this case up to zone 24.
Note: ID limit for zone allocation SPC 4000: Expander ID 1–3. SPC 5000: Expander ID 1–15. SPC 6000: Expander ID 1–63.
|
ID |
|
Zone |
ID |
|
Zone |
ID |
Zones |
ID |
Zones |
ID |
Zones |
|---|---|---|---|---|---|---|---|---|---|---|---|
|
1 |
9-16 |
14 |
113-120 |
27 |
217-224 |
40 |
321-328 |
53 |
425-432 |
||
|
2 |
17-24 |
15 |
121-128 |
28 |
225-232 |
41 |
329-336 |
54 |
433-440 |
||
|
3 |
25-32 |
16 |
129-136 |
29 |
233-240 |
42 |
337-344 |
55 |
441-448 |
||
|
4 |
33-40 |
17 |
137-144 |
30 |
241-248 |
43 |
345-352 |
56 |
449-456 |
||
|
5 |
41-48 |
18 |
145-152 |
31 |
249-256 |
44 |
353-360 |
57 |
457-464 |
||
|
6 |
49-56 |
19 |
153-160 |
32 |
257-264 |
45 |
361-368 |
58 |
465-472 |
||
|
7 |
57-64 |
20 |
161-168 |
33 |
265-272 |
46 |
369-376 |
59 |
473-480 |
||
|
8 |
65-72 |
21 |
169-176 |
34 |
273-280 |
47 |
377-384 |
60 |
481-488 |
||
|
9 |
73-80 |
22 |
177-184 |
35 |
281-288 |
48 |
385-392 |
61 |
489-496 |
||
|
10 |
81-88 |
23 |
185-192 |
36 |
289-296 |
49 |
393-400 |
62 |
497-504 |
||
|
11 |
89-96 |
24 |
193-200 |
37 |
297-304 |
50 |
401-408 |
63 |
505-512 |
||
|
12 |
97-104 |
25 |
201-208 |
38 |
305-312 |
51 |
409-416 |
||||
|
13 |
105-112 |
26 |
209-216 |
39 |
313-320 |
52 |
417-424 |
||||
|
If 2 devices of a kind (for example, expanders) are set to same ID, upon configuration, both expanders beep and the flashing LED indicates conflict. Reset the switches and the system rescans. On a device, if both rotary switches are set to zero (0, 0), the full configuration becomes an automatic addressing configuration. |
To select the ADDRESS MODE:
-
Scroll to ADDRESS MODE.
-
Press SELECT.
-
Toggle for appropriate address mode: AUTOMATIC or MANUAL
-
Press SELECT to update the setting.